Outdoor Living

Microcement Driveways: A Modern Alternative to Concrete and Pavers

Most driveway calls we get in Los Angeles aren't from people who want to rip out concrete and start fresh. They're from people staring at a slab that's cracked in three places, stained with twenty years of oil drips, and patched in a color that doesn't match the rest of it. Repouring means jackhammers, a dumpster, and a week or two where you're parking on the street. Microcement skips that entirely — it goes down over the slab you already have.

Resurfacing Over an Existing Slab

If the concrete underneath is structurally sound — no heaving, no major settling — we don't need to touch it. We prep the surface, prime it, and build up two to three thin coats of microcement directly on top, finishing around 2 to 3mm total thickness. That's thin enough that it doesn't change the height of the driveway relative to the garage floor or the street, which matters more than people expect when there's a transition at the garage door threshold.

The old cracks don't show through. Hairline cracking in the original slab gets bridged during prep, usually with a reinforcing mesh or crack-isolation membrane depending on how bad it is, so what you're driving on afterward is one continuous surface instead of a slab with visible fault lines running through it.

Why a Patchwork of Pavers Isn't the Only Option

Pavers get chosen a lot for driveways because they hide flaws in the base and they're replaceable one at a time. But they come with their own maintenance list — joints that need re-sanding, individual units that shift or sink over years of car weight, weeds working up through the gaps. A microcement driveway is one seamless surface with no joints for anything to work its way into. There's also no pattern to align or match if a section ever needs attention, since it's a single monolithic finish rather than hundreds of individual pieces.

The tradeoff is worth being honest about: pavers give you texture and depth that's hard to replicate, and if a paver cracks you swap that one unit. Microcement gives you a clean, unbroken plane instead — it's a different look, and it suits a more modern or minimal home exterior better than a busy paver pattern would.

Built for Actual Driveway Use

A driveway isn't a bathroom floor — it takes tire weight, turning scrub from the front wheels, dropped tools, the occasional oil drip. We account for that in the sealer, not the microcement itself. Outdoor driveway sealers get a coarser aggregate broadcast into the topcoat for grip and abrasion resistance, along with UV stabilizers so the color doesn't chalk out under direct Southern California sun the way an indoor-rated sealer would within a year or two. We also add an anti-slip profile to the finish, since a smooth sealed surface gets slick when it's wet, and driveways deal with sprinkler overspray and rain even in a dry climate.

For color, most driveway clients go with warm grays or sand tones that read close to the concrete they're used to, just even and unstained. Because it's one continuous pour rather than individual units, there's no variation between batches the way you sometimes get with pavers ordered at different times.

What the Install Actually Looks Like

We start with a walkthrough to check the slab's condition — grade, drainage, any spots where water pools instead of running off, since that has to be addressed before anything goes down. Prep includes grinding the surface for adhesion, patching any deep spalling, and priming. Then the microcement coats go on, each one curing before the next, followed by the sealer. A typical single-car driveway runs a few days from start to finish; wider or longer driveways take a bit more, mostly because of dry time between coats rather than labor. Either way, it's a fraction of the time and mess of a full repour, and you're not paying to haul off and dispose of a slab that was structurally fine to begin with.

One thing we always check upfront: slope and drainage. If water isn't already draining away from the garage and toward the street, we address that during prep, because sealing a surface doesn't fix a grading problem — it just makes standing water more visible.

Curb Appeal Without Redoing the Whole Front Yard

A driveway is one of the largest visible surfaces on most LA lots, and it sets the tone before anyone reaches the front door. Because the finish is continuous and hand-troweled rather than assembled from units, we can carry the same tone from the driveway into an entry walkway or a side path without the material seams you'd get transitioning between different paver styles or between concrete and a stepping-stone path. Clients doing a broader exterior refresh often have us tie the driveway, entry path, and sometimes a porch or stoop together in one finish, which reads as more deliberate than a driveway that was clearly done as a separate project from everything around it.

Is It Right for Your Driveway?

If your slab is cracked or stained but structurally fine, microcement is usually the more efficient fix — faster, less disruptive, and no debris leaving the property. If the slab itself has real structural problems, sinking, major heaving from tree roots, that's a foundation issue no surface treatment solves, and we'll tell you that directly during the consultation rather than resurfacing over a problem that's going to come back. We'd rather turn down a job that isn't a good fit for the material than sell a resurfacing job over a slab that needs actual foundation work first.

Curious what your driveway would look like resurfaced? See the finishes and colors we use for exterior work.

Explore Driveway Applications
Close-up texture of sand-tone microcement finish — project near Los Angeles in Marina del Rey

Thinking about resurfacing your driveway?